Cisco aironet client utility windows 7

Tap OK. The driver and client utility installation is complete. To verify that you have properly installed the driver and client utilities, check the client adapter's LEDs.

If the installation was successful, the client adapter's green LED blinks. This section describes resolved and open caveats for client utility and driver release 2. When Chariot upstream Filesndl. Running PSC by itself does not have a low throughput. However, if you set the same key in index 1 but set the transmit key to another key, the ACU does not request a WEP key and the client associates correctly. Net 4. The controller disassociates and deauthenticates the client and deletes its context, but the client reassociates before its second disconnect timer expires and notifies the Windows CE stack.

The client already has an IP address, but the controller creates a new context and is not aware that the client has an IP address. The following caveat is not resolved in client utility and driver release 2. The ACU is installed on the device. When the device goes out of radio coverage range but later comes within range, the device does not automatically associate to the access point.

For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at. Then choose your product and Troubleshooting to find information on the problem you are experiencing. For more information about Cisco Aironet series client adapters for Windows CE, refer to the following documents:. Cisco documentation and additional literature are available on Cisco.

Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco documentation and additional literature are available in the Product Documentation DVD package, which may have shipped with your product. The Product Documentation DVD is updated regularly and may be more current than printed documentation. The Product Documentation DVD is a comprehensive library of technical product documentation on portable media.

The DVD enables you to access multiple versions of hardware and software installation, configuration, and command guides for Cisco products and to view technical documentation in HTML. With the DVD, you have access to the same documentation that is found on the Cisco website without being connected to the Internet. Certain products also have. Registered Cisco. Beginning June 30, , registered Cisco.

Nonregistered Cisco. You can also order documentation by e-mail at tech-doc-store-mkpl external. You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.

You can submit comments by using the response card if present behind the front cover of your document or by writing to the following address:.

A current list of security advisories and notices for Cisco products is available at this URL:. This name is included in the access point's list of connected devices. Note Each computer on the network should have a unique client name. Step 16 Select Data Rates under Property. Make sure that Auto is selected in the list of options in the Value box. Specifies the rate at which you want your client adapter to transmit or receive packets to or from access points in infrastructure mode or other clients in ad hoc mode.

Auto is recommended for infrastructure mode; setting a specific data rate is recommended for ad hoc mode. Uses the Mbps data rate when possible but drops to lower rates when necessary. Note Your client adapter's data rate must be set to Auto or must match the data rate of the access point in infrastructure mode or the other clients in ad hoc mode with which it is to communicate.

Otherwise, your client adapter may not be able to associate to them. Step 17 Click OK. The driver and client utility installation is complete. The client adapter has been installed and configured for basic operation.

Go to the "Verifying Installation" section to determine if the installation was successful. Then if you want to enable security features for the client adapter, go to Chapter 4. Note If you want to be able to use the client adapter on another Windows CE device, you can install the driver and client utilities on that device without having to complete all of the previous steps. After you have installed the driver and client utilities for your client adapter on a Windows CE device, you can prepare other Windows CE devices with the same operating system 2.

Note After the WinCE2. Follow the steps below to install the driver and client utilities on other Windows CE devices using an abbreviated procedure. Note This step assumes that the default install was used for ActiveSync. Step 3 Double-click CeAppMgr. To verify that you have properly installed the driver and client utilities and minimally configured your client adapter, check the client adapter's LEDs.

If the installation was successful, the client adapter's green LED blinks. Note If your installation was unsuccessful or you experienced problems during or after driver installation, refer to Chapter 8 for troubleshooting information. Skip to content Skip to search Skip to footer.

Book Contents Book Contents. Find Matches in This Book. Thank you for your support! We're happy to announce that we met our goal for the Community Helping Community campaign! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for. Did you mean:.

All Community This category This board. Wireless - Mobility Blogs. In some cases, there may be an abnormality in one of the part files of these COS APs, which makes it impossible to convert to Mobility Express. At this time, you will encounter the following error. Read More. Sudhagar Singh.

Announcing Cisco Wireless Catalyst - We are excited to announce the Second refresh of After previous Everyone's tags 7 : Amilee San Juan.

Announcing Cisco Wireless 8. We are excited to announce the third refresh of 8. While the CCO release of 8. The CCX program ensures the widespread availability of client devices that are interoperable with a Cisco Wireless LAN WLAN infrastructure and take advantage of Cisco innovations for enhanced security, mobility, quality of service, and network management. Cisco does not sell or support Cisco Compatible client devices, but the device manufacturers do.

A program participant, such as the maker of a WLAN client adapter or client device, implements support for all features and then submits the product to an independent lab for rigorous testing. The device can earn the right to be called Cisco Compatible only if the device passes all the tests.

Specifically, ACM enables you to access status information about your client adapter and perform basic tasks. For Cisco Aironet Specifically, ASTU enables you to access status information about your client adapter and perform basic tasks. Note: Sometimes, you need to select the utilities that you want to install during the client software installation.

The ADU profile manager feature enables you to create and manage up to 16 profiles or saved configurations for your client adapter. When you try to add more than 16 profiles, this message appears:. These profiles enable you to use your client adapter in different locations, each of which requires different configuration settings.

For example, you can set up profiles to use your client adapter at the office, at home, and in public areas such as airports. After you create the profiles, you can easily switch between the profiles without a need to reconfigure your client adapter each time you enter a new location. Profiles reside in the registry.

You lose any saved profiles if you uninstall the software on the client adapter. No, this cannot be accomplished with ADU profiles. This is the max. You can add a key in the driver hive registry in order to adjust RTS. Cisco recommends that you do not change this value for general deployment because it can interfere with the rate adaptation algorithms.

Directed roaming is supported in CCXv4 and later. Cisco does not really do directed roaming the controller does not tell client to roam to a specific access point but does send these parameters to clients for clients to make roaming decisions.

These are only for CCXv4 and later clients. This will not affect clients which have a CCX version earlier than 4. Check the driver for your PC card socket. If the driver is a CardBus driver, check whether it is bit only. The Cisco Aironet card requires bit access. If the driver for the socket only works in bit mode, you must contact the manufacturer of the computer for a bit version.

If the manufacturer cannot provide you with one, there are third-party PCMCIA card and socket service manufacturers who sell products that support bit access. An access point has the physical capacity to handle 2, MAC addresses.