Installing original floyd rose tremolo

The exact depth at this stage isn't critical. Were just establishing the location of the post holes to start with. A Forstner bit can be used to remove some of the waste within the 24mm x 76mm cut-out of the insert template to a depth of approx. The insert plate can now be removed from the indexer and the overlay plate installed over the top. Again, use the Forstner bit to remove some of the waste to a depth of 5mm. Creating the rear well that allows the bridge to be pulled backwards when raising the trem arm requires routing a secondary depth at the back of the cavity of an additional 6mm.

This is achieved by fitting the small stop bar to the overlay template that reduces the router lateral travel by 16mm. Run the router within the template to a depth of 12mm below the face of the guitar body. The indexer and templates can now be removed from the body. Using a drill press bore all the way through the body down through the bottom of the sustain block rout.

The exact location and size of this hole isn't critical, just as long as it is as close to the front edge of the rout as possible. Where the drill exits the body at the rear, mark a line perpendicular to the centre of the body that touches the tangent of this drill hole. This line should now align with the front edge of the sustain block rout and is used for locating the final template for routing the spring cavity.

Fit and clamp the fourth template, aligning it with the centre and sustain bock reference lines on the back of the body. If your body is a different thickness this will change how deep this rout must be. The rout needs to be deep enough to allow clearance for the springs and sustain block, but not so deep that you risk punching through the underside of the pickup routs. Ideally this depth should be [thickness of body] - 29mm. An additional depth to the rear edge of the spring cavity is required to allow clearance for the sustain block to swing backwards when the trem arm is depressed.

This depth is again dependent on the thickness of your body but should be [thickness of body] - 15mm. For a typical Strat this will result in a cutting depth of 30mm.

The resultant rout will leave a small 3mm ledge of timber that is visible when viewing back through the sustain block cavity. Take care not to run the bit into the forward edge of the sustain block rout.

A temporary fence may be clamped to the work piece to prevent the router being accidentally moved into the front wall of the sustain block rout. The last step is to bore the final depth of the trem bushing holes. Remove the last template and flip the body over. Measure the length of your trem bushings and set your drill press depth stop to this value. Using a 10mm brad point bit on the drill press bore down the two 10mm holes that were established in step 2.

Once the holes have been drilled the bushings can be pressed into the guitar. They should go in with firm hand pressure.

An alternate method is to use a drill press with a short piece of dowel in the chuck to press the bushings in. Sale Sold Out. Floyd Rose Product Type Tremolos.

Locking nut sold separately. Returns Policy You may return most new, unopened items within 30 days of delivery for a full refund. Shipping We can ship to virtually any address in the world. Quick view. Plus, he encounters his first Floyd Rose. They are listed to help users have the best reference. ListAlternatives worked without a stop to update continuously as well as select from trusted websites.

On our site, you can freely click anything without paying any cost, yet when you click the links to other sites, we will not ensure this, it entirely depends on each site, apps, products, You can make your review for alternatives in the form of an article, then send it to us as a DOC file. We accept all proposals, reviews, user feedback via email. Please visit Contact Us to get the email address. Usually, they are. Join us, we promise to give users new and great experiences more than what you expect.

Original Tremolo System - Floyd Rose trend floydrose. The Floyd Rose Original is precision-made in Germany, engineered to exacting specifications using high-quality hardened steel and a nickel-plated brass sustain block. Visit site. Official Floyd Rose Tremolo Systems great floydrose. Quick view. Do both sides to align the bridge evenly. You don't want to have your 6th hanging off at the 15th fret, do ya? Once the bridge is aligned, you need to figure where the holes for the pivot screws are going to go.

Here is an interesting tidbit: Notice how the strings are not directly above the pole pieces on the humbucker. This is standard size Seymour Duncan pickup, but they also make the same model pickups slightly more spaced on the pole pieces, called Trembuckers , to line up the strings and look pretty on guitars with Floyd Rose bridges and I suspect other bridges as well : I have used both spaced pickups for many years with no noticeable difference in tone, but that is just me!

Now here you really need to focus and pay attention. Trace the outline of your bridge on the guitar with a pencil, then carefully measure the bushings and drawing to find where you will put your pilot holes for the pivot screws.

You've heard measure twice, cut once? Don't do it half assed the first time. If you do screw up the holes. Fill them with wooden dowel available at the hardware store and redrill.

Once you find the right spots, drill! Start off with a small bit, and gradually move up. I used 6 bits from start to finish before my hole was big enough for the bushing. If you have access to a drill press, use it! You connect your drill and it provides a nice stand. As you can see it works just fine. Once your holes are drilled, work up a glob of spit and spit in each new hole.

This is to provide a lube to help the bushings go in easier. Gently tap the bushings into place using a piece of wood on top of the bushing so you don't damage it with your gorilla hands and the hammer.

If you are felling too much resistance, stop, and make sure the hole is big enough.